The "Slide-Ezzz" Sliding Door Repair Kit is for sliding glass patio doors that don't slide good at all due to:
* worn out sliding door track,
* worn out sliding glass door wheels or rollers
* or both.
There are 256 DIFFERENT TYPES AND STYLES OF glass sliding door WHEELS and ROLLERS on the market.
Good luck on finding the right replacement rollers or wheels for your sliding glass door.
By putting a hard, Teflon impregnated, specially formed, slippery plastic on the corners of the sliding door (Corner Brackets) and gluing down a hard, flat, slippery plastic on the door track or threshold (Tracking Strips), the sliding door then slides Teflon on plastic.
The Teflon impregnated material used for the "Corner Brackets" was originally designed for very abusive applications, such as chain guides.
Therefore, the "Kit" should LAST FOR THOUSANDS AND THOUSANDS OF CYCLES OR FOR YEARS & YEARS!
The 8 foot long "Tracking Strips" come in either white or black to best match your sliding door frame color.
Additional "Tracking Strips" can be purchased for larger sliding doors.
No need to remove existing sliding glass door hardware!
Watch our Detailed Installation Video
The sliding door will SLIDE LIKE NEW! QUIET TOO!
** Kit can be usually be INSTALLED IN AN HOUR OR LESS - - - - - WITHOUT REMOVING THE DOOR! **
Quick Installation Instructions
1) Thoroughly clean the sliding door track to remove all grease, oil, dirt and debris.
2) Just slide the two plastic strips under the sliding door, cut to length and glue on.
3) Put the Teflon impregnated pieces on the corners of the door, screw on and lubricate. That's it. Your done!
IT'S JUST THAT EASY! Be careful not to throw the door through the wall!
REPAIRS MOST SLIDING GLASS DOORS!
There is a 60 day money back warranty if your not happy with the performance of the product and a one year manufacturers warranty on all parts.
2 - 8 foot long, hard slippery flat plastic "Tracking Strips"2 - Specially formed Teflon impregnated "Corner Brackets"8 - Shims for adjustment1 - Tube of Adhesive
4 - Self drilling Phillips Head screws
Teflon impregnated "Corner Brackets" come in black and use the existing roller rail as a guide so the door slides straight. Shown here with shims and screws.
"Tracking Strips" or the hard, slippery plastic strips that are glued to the threshold come in either black or white.
Kit includes all the parts, including screws and adhesive, to repair one standard sliding glass patio door up to 8 feet in length.
Additional "Tracking Strips" can be ordered for sliding patio doors longer than 8 feet in length.
There is no need to order or use any other type of sliding door replacement hardware when using the "Slide-Ezzz" Sliding Door Repair Kit.
IMPORTANT PRODUCT NOTES:
The "Tracking Strips" are 1/8 inch thick and the "prongs" that go under the door on the "Corner Brackets" are 1/4 inch thick.
Therefore you will need 1/2 inch of room (giving 1/8" of "slop margin" so the door doesn't bind) between the flat portion of the threshold or sliding door track and the bottom of the sliding door to install this "Kit". Pick up on the sliding door and measure to make sure there is enough room.
For lower level beachfront sliding doors, use only one "Tracking Strip" on the inside as the wind blows the sand against the sliding door threshold track and using the "Tracking Strip" on the outside may cause the door to be hard to slide and the "Sliding Door Repair Kit" may not last as long as all the weight of the door is placed on a smaller surface area. You can use our "Sliding Door Rebuild Kit" instead for this application.
Product also DOES NOT WORK on doors with a "U" shaped frame as the "Corner Brackets" need a flat surface on which to be adhered.
A door with a "U" shaped frame is pictured below:
A work around for a "U" shaped door is to use a "Dremel Tool" or sander to shape the "Corner Bracket" like in the picture below: